Power-on self-test?

eine frage, nach dem einschalten gibt es noch keine maschinenbefehle im ram, die nach neumann decode, und ausgeführt werden kann, das bedeutet doch, das die cpu zunächst über den microcode, den code, maschinembefehle, im rom ansprechen muss, werden diese befehle nun in den befehlsdecoder geladen, befehlszähler erhöht und dann die nächste adresse im rom angesprochen

oder ist es so dass, die post routinen erst komplett in den ram geladen werden und dann die neumann routinen durchgeführt werden, also fetch, decode und so weiter

ausgeführt werden

:)

 

Welches Netzteil hast du da drin ?

Das MB hat nicht einmal eine Debug LED die den POST anzeigt, um sich zu vergewissern woran das liegt, aber wenn du kein Signal bekommst geht der Power on self Test nicht weiter als zum Speicher, Teste ihn mal einzeln in DIMM Slot 2 von links der CPU

 

Was da jetzt wirklich schiefgelaufen ist/kaputt ist kann man aus der Ferne nahezu unmöglich sagen - was ich dir aber definitiv sagen kann ist, dass ein PC der nur noch piepst und gar nichts mehr von sich gibt (du also nicht mal mehr ins BIOS kommst?) ein anderes Problem hat als Windows - denn Windows kommt erst später ins Spiel nachdem der Power on self test ("POST") erfolgreich war.

Solltest du also tatsächlich nicht mal mehr ins BIOS kommen (mal direkt nach dem Start auf entf und/oder F2 rumtippen) haste ein Hardwareproblem aber kein Windowsproblem.


Ist das "biepbiep" was dein Board macht ein anderes als gewöhnlich? Falls ja ist das ein sogenannter Beep-Code der dir verraten könnte wo das Problem liegt. Welche Piepreihenfolge was bedeutet steht in deinem Mainboardhandbuch. *sm_B-)

 

AW: [Sammelthread] Der LW Laufzeit - Hall of Fame - Thread

Ich habe leider keine Möglichkeit, auf die SMART-Daten der Festplatte im Router über eine grafische Oberfläche zuzugreifen, daher kann ich nur den Konsolenauszug posten:

Aleph jimini # smartctl -a /dev/sda smartctl 5.40 2010-10-16 r3189 [i686-pc-linux-gnu] (local build) Copyright (C) 2002-10 by Bruce Allen, smartmontools === START OF INFORMATION SECTION === Model Family: Fujitsu MHV series Device Model: FUJITSU MHV2120BH Serial Number: NWAPT6926JGB Firmware Version: 00000029 User Capacity: 120.034.123.776 bytes Device is: In smartctl database [for details use: -P show] ATA Version is: 7 ATA Standard is: ATA/ATAPI-7 T13 1532D revision 4a Local Time is: Fri Aug 19 11:23:37 2011 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 702) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 82) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 100 100 046 Pre-fail Always - 133532 2 Throughput_Performance 0x0005 100 100 030 Pre-fail Offline - 31784960 3 Spin_Up_Time 0x0003 100 100 025 Pre-fail Always - 1 4 Start_Stop_Count 0x0032 099 099 000 Old_age Always - 2412 5 Reallocated_Sector_Ct 0x0033 100 100 024 Pre-fail Always - 0 (2000, 0) 7 Seek_Error_Rate 0x000f 100 100 047 Pre-fail Always - 2437 8 Seek_Time_Performance 0x0005 100 100 019 Pre-fail Offline - 0 9 Power_On_Seconds 0x0032 063 063 000 Old_age Always - 18766h+47m+57s 10 Spin_Retry_Count 0x0013 100 100 020 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 2277 192 Power-Off_Retract_Count 0x0032 099 099 000 Old_age Always - 260 193 Load_Cycle_Count 0x0032 091 091 000 Old_age Always - 195248 194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 37 (Min/Max 7/58) 195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always - 7805 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0 (0, 6592) 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x000f 100 100 060 Pre-fail Always - 24537 203 Run_Out_Cancel 0x0002 100 100 000 Old_age Always - 429509441668 240 Head_Flying_Hours 0x003e 200 200 000 Old_age Always - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. Zum Vergrößern anklicken....

Als kleiner "Beweis" noch ein Screenshot des Fensters:






Ich bin überrascht, wie wacker sich die Platte schlägt. Vorher lief sie knapp zwei Jahre in meinem Notebook, seit Anfang 2009 sitzt sie im Router (seit 351 Tagen läuft der ohne Reboot).

MfG Jimini

 

AW: [Sammelthread] Der LW Laufzeit - Hall of Fame - Thread

Ich hole mir mal den 10ten Platz der SSDs.

5.064 | blackout24 | Crucial M4 | 64 GB @ 2,5" | 1.051

Code:

ich@localhost ~ % sudo smartctl -a /dev/sda smartctl 6.0 2012-10-10 r3643 [x86_64-linux-3.6.8-1-ARCH] (local build) Copyright (C) 2002-12, Bruce Allen, Christian Franke, www.smartmontools.org  === START OF INFORMATION SECTION === Model Family:     Crucial/Micron RealSSD C300/C400/m4 Device Model:     M4-CT064M4SSD2 Serial Number:    000000001203032B4BF9 LU WWN Device Id: 5 00a075 1032b4bf9 Firmware Version: 000F User Capacity:    64.023.257.088 bytes [64,0 GB] Sector Size:      512 bytes logical/physical Rotation Rate:    Solid State Device Device is:        In smartctl database [for details use: -P show] ATA Version is:   ACS-2, ATA8-ACS T13/1699-D revision 6 SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 1.5 Gb/s) Local Time is:    Thu Dec  6 10:07:29 2012 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled  === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED  General SMART Values: Offline data collection status:  (0x80)	Offline data collection activity 					was never started. 					Auto Offline Data Collection: Enabled. Self-test execution status:      (   0)	The previous self-test routine completed 					without error or no self-test has ever  					been run. Total time to complete Offline  data collection: 		(  295) seconds. Offline data collection capabilities: 			 (0x7b) SMART execute Offline immediate. 					Auto Offline data collection on/off support. 					Suspend Offline collection upon new 					command. 					Offline surface scan supported. 					Self-test supported. 					Conveyance Self-test supported. 					Selective Self-test supported. SMART capabilities:            (0x0003)	Saves SMART data before entering 					power-saving mode. 					Supports SMART auto save timer. Error logging capability:        (0x01)	Error logging supported. 					General Purpose Logging supported. Short self-test routine  recommended polling time: 	 (   2) minutes. Extended self-test routine recommended polling time: 	 (   4) minutes. Conveyance self-test routine recommended polling time: 	 (   3) minutes. SCT capabilities: 	       (0x003d)	SCT Status supported. 					SCT Error Recovery Control supported. 					SCT Feature Control supported. 					SCT Data Table supported.  SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE   1 Raw_Read_Error_Rate     0x002f   100   100   050    Pre-fail  Always       -       0   5 Reallocated_Sector_Ct   0x0033   100   100   010    Pre-fail  Always       -       0   9 Power_On_Hours          0x0032   100   100   001    Old_age   Always       -       5064  12 Power_Cycle_Count       0x0032   100   100   001    Old_age   Always       -       1051 170 Grown_Failing_Block_Ct  0x0033   100   100   010    Pre-fail  Always       -       0 171 Program_Fail_Count      0x0032   100   100   001    Old_age   Always       -       0 172 Erase_Fail_Count        0x0032   100   100   001    Old_age   Always       -       0 173 Wear_Leveling_Count     0x0033   100   100   010    Pre-fail  Always       -       19 174 Unexpect_Power_Loss_Ct  0x0032   100   100   001    Old_age   Always       -       978 181 Non4k_Aligned_Access    0x0022   100   100   001    Old_age   Always       -       59 18 41 183 SATA_Iface_Downshift    0x0032   100   100   001    Old_age   Always       -       0 184 End-to-End_Error        0x0033   100   100   050    Pre-fail  Always       -       0 187 Reported_Uncorrect      0x0032   100   100   001    Old_age   Always       -       0 188 Command_Timeout         0x0032   100   100   001    Old_age   Always       -       0 189 Factory_Bad_Block_Ct    0x000e   100   100   001    Old_age   Always       -       48 194 Temperature_Celsius     0x0022   100   100   000    Old_age   Always       -       0 195 Hardware_ECC_Recovered  0x003a   100   100   001    Old_age   Always       -       0 196 Reallocated_Event_Count 0x0032   100   100   001    Old_age   Always       -       0 197 Current_Pending_Sector  0x0032   100   100   001    Old_age   Always       -       0 198 Offline_Uncorrectable   0x0030   100   100   001    Old_age   Offline      -       0 199 UDMA_CRC_Error_Count    0x0032   100   100   001    Old_age   Always       -       0 202 Perc_Rated_Life_Used    0x0018   100   100   001    Old_age   Offline      -       0 206 Write_Error_Rate        0x000e   100   100   001    Old_age   Always       -       0  SMART Error Log Version: 1 No Errors Logged  SMART Self-test log structure revision number 1 No self-tests have been logged.  [To run self-tests, use: smartctl -t]   SMART Selective self-test log data structure revision number 1  SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS     1        0        0  Not_testing     2        0        0  Not_testing     3        0        0  Not_testing     4        0        0  Not_testing     5        0        0  Not_testing Selective self-test flags (0x0):   After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.

 

Warum muss z. B. crystaldiskinfo noch immer in jedem Thema mit (vermuteten) HDD-Problemen erwähnt werden? *Noahnung :ka:*Noahnung :ka:
Self-Monitoring, Analysis and Reporting Technology – Wikipedia